helical bevel gear reducer

The EP Series Helical Bevel Reducer provides unmatched performance, durability, and design flexibility. This unit provides torque capacities up to 20,000 Nm (14,750 ft pounds).
The cat4CAD software allows simple interactive product selection of the entire gearbox and gear-electric motor system. Cat4CAD facilitates you in choosing and configuring these products, gives you the chance to print out extensive technical data linens, and generates complete 2D drawings and 3D models for direct download.
11 sizes
Insight power capacities from 0.16 to 120 HP
Gear ratios from 5:1 to 8900:1
Torque capacities to 20,000 Nm
Inverter duty course F insulated motor windings
Class 12 Helical and Spiral Bevel Gears: Provides higher efficiencies and better torques in helical bevel gear reducer smaller sized sizes.
Multiple Input Options: Essential gear motors, inch or metric shafts, NEMA, IEC, and servo adapters provide unmatched drive versatility.
Multiple Output Choices: Hollow bores and shrink disks for shaft mounting, inch and metric output shafts, mounting pilots and flanges offer an array of design solutions.
UNIBLOCK Housing: For optimum rigidity, universal installation on five sides or with a torque arm.
Worldwide Engine: Multiple leads and windings for worldwide multi volt/Hz requirements in addition modular design to accept brakes, encoders or pressured cooling.
High efficiency motor design available
Innovative self-locking, self-aligning taper shaft engine connection
Gearbox supplied factory filled with synthetic oil
Corrosion and shock resistant cast iron housing
High efficiency helical-bevel gears. 98% per stage
Normally closed breather with multiple locations (Optional OtN2000)
Double lip seals upon heat treated, plunge surface shafts
Shaft mounting choices include tapered bushings designs
This is a comprehensive offering of energy-efficient, right angle helical bevel enclosed gearing. It is available as gearmotors and a variety of reducers with torque capacities up to 119,000 inch pounds. Housing designs include footed, encounter and flanged configurations. Gearmotors can be found in three stage high efficiency designs through 50 HP and single phase to 5 HP. We provide a selection of input and output shaft options. Additionally, you will find fixed and variable quickness motors and range of ratios available in this product offering.
Features
Accommodates insight power from ¼ Hp to 75Hp
Torque ratings up to 119,489 in-lbs
Reduction ratios up to 7,500:1
Helical – bevel – helical gear train offers cost effective high and low speed solutions
Up to 94% efficient
Four input options available for all units
Two output flange options – B5 and B14
Multiple output shaft interfaces
Critical dimensions interchangeable with major competitors
Modifications / Accessories
Integral Gearmotor
Clamp Collar C-Face Input
Solid Shaft Input
3-Piece Coupled C-Face Input
CEMA Screw Conveyor Adapter
EZ Kleen Washdown Package
XT Output Seals
Backstop
DURABLE Output Bearings
Inch or Metric Dimensions
Common Applications
Troughing Belt Conveyors
Slider Bed Conveyors
Mixer Drives
Screw Conveyors
Bucket Elevators
General Industrial Machinery
Common Industries
Aggregate and Cement
Air Handling
Chemical, Oil, and Gas
Food, Beverage, and Pharmaceutical
Paper and Forest
Unit and Baggage Handling
Water and Wastewater
As per the growing and varying demands of customers, you can expect an array of Helical Bevel Gear Reducers. The technological content material of our products permits an extraordinary performance/lifespan ratio. The extremely versatile Helical Bevel Gear Reducers we provide are successfully found in a multitude of industrial and civil applications. These are B-Series units which offer excellent value for money and output torque/weight ratio, especially considering that they need not a lot of servicing. Besides these, our products are available in cast iron (sizes 063 to 163) or aluminium (sizes A42 to A73) casing.
Features:
Sizes: 060-080-100-125-140-150-160
Available versions: B-fitted for electric motor coupling, IB with input shaft, CB with small motor, PB-fitted for electric motor coupling with flexible joint
Casing with foot FC, flange SC and universal UC
Switch on to 90 kW
Gears hardened and tempered with shaved or surface profile
Gearing with 3 decrease stages
Gleason spiral bevel gear pairs with run-in profile, mounted as second decrease stage for an increased resistance
Reduction ratios between 5, 71 and 187, 24
Torque max 13.000 Nm and admissible radial loads max 80.000 N
High-power casings optimized with FEM analysis and input and result flanges of grey cast-iron G200 to make sure best level performances and high reliability
Load capacity calculated and verified according to ISO 6336 and AGMA 2001
Painted with RAL 5010 blue epoxy-polyester powder
Accessories: torque arm, result flange, output shaft, shrink disk, backstop device, protection cover kit, viton oil seals, reinforced output, assemble/disassemble kit
Series EP right angle helical bevel gear motors offer ratios from 8:1 to 160:1 in three stages or up to 10000:1 in five levels. Motors are available up to 90kW and output torque capacity up to 12,300 Nm.
The series EP helical bevel gear motor is designed with integral cast feet for base or end mounting and may be offered with single or double extended output shafts.
Models are also available since shaft mounted or with output flanges and are designed for installation horizontally or vertically. The models can also be offered with a bolt on torque response bracket and all variants are available either motorised or with an insight shaft assembly.
Adding to the brand new range of Ever-Power helical gear motors this product takes benefit of our many years of accumulated design knowledge together with the use of high quality materials and components. The end result is a series of velocity reducing geared motors providing high load carrying capacities, increased efficiency, peaceful running and reliability.
Features of Helical Bevel Gear Motor
Standard motor connection
Capability to fit double essential oil seals, on input and output shaft because required.
All systems are dimensionally interchangeable with various other major manufacturers.
Units are produced and assembled from a family group of modular kits for distributor friendliness minimizing inventory and maximizing availability.
Motorized units can be installed with a backstop module and reducer Systems can be installed with a backstop and fan.
Applications:
-Conveyors, Agitators, Elevators, Cranes, Crushers
-Helical Bevel gear motors are found in industries such as chemicals, pharma, packaging, food processing, plastic material and automation etc.
Key Features:
Sizes: A40-A50-A70
Offered versions: EP – fitted for electric motor coupling, IEP – with input shaft, CEP – with small motor
Cases with foot, flange or universal
Switch on to 4,8 Kw
Gears with shaved or ground profile
Gearing with 2 and 3 reduction stages
Hypoid bevel gears for size A40 and A50, gleason bevel gear pairs for size A70, all with run-in profile
Reduction ratios between 7,62 and 442,76
Torque max 450 Nm and admissible radial loads max 5.500 N on hollow shaft and 10.000 N on solid shaft
Cases in die-cast aluminium alloy
Exceptional mechanical strength while being and particularly lightweight
Load capacity calculated to ISO6336 and verified according to AGMA 2001-B88
Painted with RAL 5010 blue epoxy-polyester powder in in accordance to DIN 1843
Accessories: torque arm, result flange, output shaft.
Generallntroduction of HK series:
Gear Reducer
The EP series gear units, are novel transmission gadget and made up of Y series electric motor, helical gear,Arc gear and worm gear. The gears are made of high wear-resisting alloy materials, specifically and finely processed.
Advantages:
1: Helical-bevel gear two-stage reducer
2: Compact structure, high efficiency
3: Quenched 20CrMnTi for gears
4: CE, ISO9001.
5: Compact design, small volume, wonderful appearance ,and solid capacity to be overloaded.
6: Precise division and wide range for transmission ratio.
7: The efficiency is up to because high as 96% with low energy intake, strong adaptability and is with the capacity of operating continually in corrosive or damp environment.
8: All- purpose use, convenient and low-price maintenance.
9: New seal gadget, strong adaptability.
10: Varied selection of motor combinations, mouting positions and struture projects.